+- AiOwares (https://www.aiowares.com)
+-- Forum: Software & Applications (https://www.aiowares.com/forumdisplay.php?fid=6)
+--- Forum: Multi-Platform Software (https://www.aiowares.com/forumdisplay.php?fid=14)
+---- Forum: Windows (https://www.aiowares.com/forumdisplay.php?fid=42)
+---- Thread: MKVToolNix v90.0 (/showthread.php?tid=573)
RE: MKVToolNix v61.0 - Alv37 - 08-31-2021
v61.0 is out
Frontpage updated.
RE: MKVToolNix v62.0 - Alv37 - 10-10-2021
v62.0 is out
Frontpage updated.
RE: MKVToolNix v63.0 - Alv37 - 11-14-2021
v63.0 is out
Frontpage updated.
RE: MKVToolNix v64.0 - Alv37 - 12-27-2021
v64.0 is out
Frontpage updated.
RE: MKVToolNix v65.0 - Alv37 - 02-07-2022
v65.0 is out
Frontpage updated.
RE: MKVToolNix v66.0 - Alv37 - 03-14-2022
v66.0 is out
Frontpage updated.
RE: MKVToolNix v67.0 - Alv37 - 04-11-2022
v67.0 is out
Frontpage updated.
RE: MKVToolNix v67.0 - Manchita - 04-18-2022
(07-07-2018, 01:20 PM)Alv37 Wrote: The contents of this section are hiddenYou have No permissionsI'm having a little problem with MKVToolNix 67 (x64). I tried the installer here and one from Nsane but when I try to start MKVToolNix I get this error message:-"The procedure entry point Create DXGIFactory2 could not be located in the dynamic link library dxgi.dll" I Googled for a solution, tried running sfc/ scannow but the error message persists. I installed the portable version in my Portable Apps Platform and it launches without any problem....but I'd like to know why the installed version gives this error I'm using Win 7 (a64) by the way. I would appreciate any advice. Thanks.
RE: MKVToolNix v67.0 - chillgates - 04-18-2022
(04-18-2022, 08:17 PM)Manchita Wrote: The contents of this section are hiddenYou have No permissions
Code:
The contents of this section are hiddenExplanation at above link may tell you answer.
RE: MKVToolNix v67.0 - Manchita - 04-19-2022
Many thanks for your reply Chillgates. I've downloaded what I think is the correct dll...I'm a bit nervous about installing it so I'll wait for a while to see how my computer acts over the next few days. When the error message first appeared it was a surprise because I have used MKVToolNix for years without any problem....and, since the portable version works fine, I was going to ignore the installed version and just use the portable one.
I searched my system with the program "Everything" and it shows there are 6 dxgi.dll's already present:-
C:\Windows\System32 (22/08/2018)
C:Windows\SysWOW64 (22/08/2018)
C:\Windows\winsxs\amd64... (21/11/2010)
C:\Windows\winsxs\amd64.... (22/08/2018)
C:\Windows\winsxs\x86... (21/11/2010)
C:\Windows\winsxs\x86.... (22/08/2018)
Thanks again.
EDIT (hours later):- After all the hours I've spent Googling and reading possible causes for this problem and trying different MKVToolNix installers, I finally stumbled onto Reddit and found some other guys who had the same problem...it's related to Windows 7. One of the guys pointed us to https://mkvtoolnix.download/windows/continuous/64-bit/67.0.0/ which lists revisions of MKVToolNix 67.0 made during the last 5 days. I downloaded the latest installer and it worked immediately, no error message. I imagine there are other people out there trying to figure out why they are experiencing this "dxgi.dll" error.
